Promaster Euro Roof Vent Adapter for 400mm x 400mm opening
Promaster Euro Roof Vent Adapter for 400mm x 400mm opening
Promaster Euro Roof Vent Adapter for 400mm x 400mm opening
Promaster Euro Roof Vent Adapter for 400mm x 400mm opening
Promaster Euro Roof Vent Adapter for 400mm x 400mm opening
Promaster Euro Roof Vent Adapter for 400mm x 400mm opening
Promaster Euro Roof Vent Adapter for 400mm x 400mm opening
Promaster Euro Roof Vent Adapter for 400mm x 400mm opening

Promaster Euro Roof Vent Adapter for 400mm x 400mm opening

Regular price $78.00
/
Shipping calculated at checkout.

Available now, Insulated Vent Fan Cover, https://www.ebay.com/itm/132946231471

Please check your fan opening size requirement!!

Patent Pending adapter matches the contour of the OEM roof so a standard RV style vent mounts to a flat surface. Prevents distorting the roof sheet metal or vent flange and can be used as an aid for locating the fan. They are CNC machined out of UV and fire resistant expanded PVC. The fan mounts to the outside adapter. Fan adapters work with the Maxxfan Deluxe series.

Fits a 400mm X 400mm opening. These fans are usually purchased in the UK. If your fan requires 14" x 14" opening please message me.

The outside adapter will fit anywhere along the center of the cargo part of the roof. Please note, if you are installing your fan towards the front of the van on the raised portion, you will not need this adapter.

The option with butyl tape includes 64" of tape. If the butyl tape is stuck to the plastic, put it in the freezer for 30 minutes. It will release, then let the butyl tape return to room temperature.

Roof Vent Adapter Install procedure: We recommend 3m Window-weld adhesive which you can get at Napa. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof supports, obviously. Make a tape line 1/4" beyond the adapter perimeter. De-gloss the area with a Scotch- brite pad. No need to scuff. Just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out. Apply three 1/8" beads of the Window-weld on the face of the adapter. Then press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use a lot of lightly set clamps and spread out the clamp force over the whole surface area. Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install. We recommend using butyl tape for the fan install. Cover the fan flange with 1 1/8" wide tape. Place onto of adapter and press down. Then drill pilot holes through the adapter and into the van roof. If the screws are going to go into a roof support beam then drill a clearance hole in the beam. You only want the screw to engage the adapter and outer skin. Use a step drill to keep from plunging through the skin. You may need longer screws. Tighten them very lightly against the fan flange. Some butyl will ooze out which you can trim off. Coat the fan flange adapter and onto the roof about 1/2" with brush on bed-liner or Flexseal from the TV guy works well. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You'll cut a lot of that piece off. Good idea to check the integrity and reapply the sealant every so often. Dicor self leveling sealant also works but looks a little messy.

If you have questions about this product you can call Hein at 541-49O-5O98