NEW!


***Not Compatible with Power Seats***
Amazing Auto swivels attach to the Driver and Passenger seat base to allow the seats to spin and latch into different positions.
- 1-1/2 inch tall
- Heavy Duty design
- Offset design allows for seat to spin without opening door
- These are not the cheap AliExpress seat swivels
Installation Video: https://youtu.be/YubKqNS78pE
All Amazing Auto swivels come with the TRUE U.S. DOT FMVSS 207 test report.
U.S. Patent Pending: 297.37.385, 297.34.122
Past DOT FMVSS 207
Sprinter years 2007-2023 D 001 and P 002
Promaster years 2014-2023 D 005 and P006
Transit years 2014-2023 D 003 and P 004
These above are all: 18.3in (465mm) x 18.3in (465mm) x 1.5in (37mm)
Chevy Express years 1997-2023 D 007 and P 008 is 14.25in. x 13.15in x 1.75in
28lbs









If you have questions about this product you can call Hein at 541-49O-5O98
WARNING!
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
- Do not exceed 40 lbs load on each tower.
- Do not extend any component more than 4" beyond forward or rearward most towers.
- Do not exceed total allowable load by vehicle manufacturer.
- Use all available attachment points on van roof.
- Do not install roof top deck or climb on rack.
- Check and tighten all hardware after 100 miles and every 500 miles there-after.
- Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.



- Delivers comparable or better performance to conventional constrained layer damping (CLD) materials and is less than half the weight
- Stand-off layer features low-density engineered stem web that optimizes damping performance
- Damps structure-borne noise when lighter materials such as thin-gauge steel, aluminum and composites are used, without adding significant weight
- Flexible, conformable material applies uniformly to complex shapes
- Adhesive backing improves wet out and won't delaminate even at high temperatures
- Can be installed in vertical or inverted applications
- Meets requirements of many OEMs for low interior VOCs
- Thickness of 2.9 mm allows for a wide range of installations where space is limited




Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.



















If you have questions about this product you can call Hein at 541-49O-5O98
DISCLAIMER
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
Do not exceed 40 lbs load on each tower.
- Do not extend any component more than 4" beyond forward or rearward most towers.
- Do not exceed total allowable load by vehicle manufacturer.
- Use all available attachment points on van roof.
- Do not install roof top deck or climb on rack.
- Check and tighten all hardware after 100 miles and every 500 miles there-after.
- Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.




Sold as a Kit. 80/20 Rail Kit for Transit.
2 Full length roof rails for Ford Transit vans with towers for Low, Mid, and High Roof Transit Vans. This kit allows you to easily add a modular solar rack to your Transit van. See our Crossbar Kits to easily add crossbars to your roof rails to build a complete solar rack kit.
** Black Anodizing may fade over time due to sun exposure.
Kits include the following plus hardware.
130WB 1 piece rail kit includes:
6 Ford Transit V2 Brackets
4 Square End Caps
2 79" 1503-LS Bars
148WB 1 piece rail kit includes:
8 Ford Transit V2 Brackets
4 Square End Caps
2 96" 1503-LS Bars
148WB 2 piece rail kit includes:
8 Ford Transit V2 Brackets
4 Square End Caps
2 72" 1503-LS Bars
2 34" 1503-LS Bars
Rail length is a total of 106"
148WB Extended 2 piece rail kit includes:
10 Ford Transit V2 Brackets
2 Ford Transit V2 Extended brackets and pads
4 Square End Caps
2 72" 1503-LS Bars
2 63" 1503-LS Bars
Rail length is a total of 135"
WARNING!
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
- Do not exceed 40 lbs load on each tower.
- Do not extend any component more than 4" beyond forward or rearward most towers.
- Do not exceed total allowable load by vehicle manufacturer.
- Use all available attachment points on van roof.
- Do not install roof top deck or climb on rack.
- Check and tighten all hardware after 100 miles and every 500 miles there-after.
- Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.




DISCLAIMER: Owner and/or installer assumes all risk associated with roof top mounted items and/or components. Owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold as is and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.









These engineered ABS plastic mud flaps offer more coverage and better protection than any other offerings. There are two parts as shown in the listing photos. The large lower portion attaches to the fender and liner and a smaller flaplet attaches to the door trim. The lower portion extends far to the inside for better protection of the vehicle under-body.
Please note that optional factory (OEM) plastic fender liners are required (not included) to install and secure these mudflaps.
****We have found that the mudflaps do not work with the aftermarket fender liners that we are selling on our site. We are currently looking into a solution.
The flaps are secured with a combination of push pins and screws plus a bracket to help stabilize the inner end of the lower part.
There is some minor drilling involved and installation is much simpler if front wheels can be removed. Be sure to support vehicle on jack stands when wheels are off.
All hardware and instructions are included. Please refer to listing photos before purchase.
You can text Hein at 54l-49O-5O98 for assistance
Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose





The material comes compressed; we recommend unpacking it as soon as it is received. One roll is 20 linear feet. 20ft long by 60 inches wide.
Arctic Fiber is a high-loft 100% non-woven, thermally bonded polyester insulation. The material is 2" thick after it lofts up. One roll of material is 20 feet long x 60" wide. This insulation is widely used in Alaska in the Van industry and has other uses in pads, covers on exterior pipe, flange valves and other special equipment.
- Allows Trapped moisture to pass through it without being held in place and drys out quickly.
- Polyester batt insulation will not promote mold growth.
- Lightweight and easily fabricated to desired dimensions with a utility knife or scissors.
- Is not an irritant and will not cause skin irritation.
- Passes the FMVSS302 burn rate test.
Recommend using a high temp adhesive spray to apply to the van skin.
Approximate amounts needed to insulate the walls, ceiling, doors and cab area:
144 WB Sprinter,148 WB Ford Transit with slider window & window in back doors = 50 linear feet
Promaster 159 WB = 60 linear feet
170 WB Sprinter = 60 linear feet
170 WB Extended Sprinter = 70 linear feet
Please call if you are in Alaska or Hawaii for shipping 541-49O-4292






WARNING!
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
- Do not exceed total allowable load by vehicle manufacturer.
- Use all available attachment points on van roof.
- Do not install roof top deck or climb on rack.
- Check and tighten all hardware after 100 miles and every 500 miles there-after.
- Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.























The RTX 2000 head unit only. Please select one of the installation kits to use with the unit.
Shop our Patent Pending AC roof adapters, seal and interior bezel to make the install easier.
The AC unit will not come with internal framing support. We highly recommend getting our framing.
Promaster rtx internal framing
IMPORTANT!! If you are ordering the DIYvan install kit please watch Hein's Video on how to install the inserts.
Compact size leaves more space for solar panels and other things on your van’s roof.
Only uses 19 amps of energy in eco mode – power consumption ranges between 10 amps to 58 amps.
Recommended to be used with a battery bank of 180 amp hours or larger.
Suitable for ambient temperatures between 41 and 126 degrees Fahrenheit.
Includes remote control.
This unit is AC only, there is no “fan only” mode for recirculating air.
One year manufacturer warranty.
The opening size is 15 1/2 by 14 1/8.
DISCLAIMER:
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.




Formed aluminum towers for directly mounting specifically sized solar panels to front and rear positions on Ford Transit vans. No crossbars or other framing needed.
Use solar panel approximately 58.3 x 26.2 like Rich Solar 200 watt model. Other panels with similar dimensions will also work.
Front position utilizes OEM (factory) roof attachment points 1 and 2 (from front) which are present on all length Transit vans (130,148 and 148 extended). Rear position utilizes OEM roof attachment points 3 and 4 which are only available on 148 regular and extended vans. See diagram (148 regular length shown)
Design is patent pending.
All hardware is included. Towers are designed for solar panels only. Some fading can occur due to sun exposure. Load on each tower not to exceed 20lbs
If you have questions about this product you can call Hein at 541-49O-5O98
DISCLAIMER
Failure to follow warnings below may allow rack to come loose from vehicle and cause injuryor death.
1. Do not exceed 20 lbs load on each tower.
2. Do not extend any component more than 4" beyond forward or rearward most towers.
3. Do not exceed total allowable load by vehicle manufacturer.
4. Use all available attachment points on van roof.
5. Do not install roof top deck or climb on rack.
6. Check and tighten all hardware after 100 miles and every 500 miles there-after.
7. Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.






For use with Weathertech mudflaps on Ford Transit van. These 'flaplets' attach to the cab doors and fill the gap left by the Weathertech flaps. They are made of black ABS plastic with haircell texture. They are attached to the door fender trim with 3 small screws. It is necessary to hand form the flaplet to have a slight curvature prior to installation. A heat gun can be used to heat the plastic so it is easier to form into slight curve that matches the door where it will be mounted. Do not over heat.
Kit includes right hand and left hand flaplets and 6 mounting screws.
To install:
1. Turn front wheels to provide clearance.
2. Hand form/bend flaplet into slight curve to match door. Using heat can help.
Textured side of flaplet should be toward back; smooth side toward tire.
3. Locate flaplet on door leaving 1/8" gap between it and top edge of mudflap below.
4. Drill 1/16 pilot holes for screws.
5. Install flaplet with screws provided. Do not over tighten or you may strip plastic trim on door.
6. Turn wheels other way and repeat on other side of vehicle.
You can text Hein at 54l-49O-5O98 for assistance.
Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose
Aluminum plate and spacer strips for covering OEM AC hole on Sprinter VS30 (2019 to present) with factory installed roof AC. Plates are .090 thick unfinished aluminum. Strips are PVC based plastic. Vent hole is 14x14.
This Plate will NOT work on the NCV3 (2007-2018) Sprinter.
Notes:
- Assembled (recommended) version comes with all strips bonded to plate. Ready to install on vehicle.
- Un-assembled version requires strips to be bonded to plate. See instructional videos below.
- A urethane structural adhesive is required to make all bonds between strips plate and vehicle.
recommended products: 3M Windoweld, Dupont Betaseal U-458plus, Sikaflex 221 - Plate is unpainted but can be painted to match vehicle.
5. RV vent flange is mounted with butyl tape provided. - Membrane sealant or tape recommended over the top of all seams recommended products: Dicor self leveling sealant or 3M 4412-N extreme sealing tape.
Best way to understand this product and installation is to watch these three videos.
Please text Hein for technical support. 541 49O 5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.



Formed Rail Kit for Promaster Vans
2 piece roof rails for Ram Promaster Van with Attachments and L Brackets. This kit allows you to easily add a modular solar rack to your Promaster. Rails and towers are Black.
We do have 1 piece rails, 114" long, for the 136 WB available for pick up only.
If you are installing solar panels we recommend Rich solar 200watt panels. We have hardware available to attach them, see our Rail Clips. Please reach out to Hein by text 541 49O-5O98 for what is recommended.
Kits include the following plus hardware.
136 Wheel Base 1 piece kit includes:
6 Promaster Attachments and Pads
6 L Brackets for formed rails
2 113.68" formed rails
Availabe for pick up only, please call.
136 Wheel Base 2 piece kit includes:
6 Promaster Attachments and Pads
6 L Brackets for formed rails
2 61.163" Front section formed rails
2 52.5" Rear section formed rails
Rail length will equal a total of 113.66"
159 Wheel Base Kit Includes:
8 Promaster Attachments and Pads
8 L Brackets for for formed rails
2 61.163" Front section formed rails
2 75.53" Rear section formed rails
Rail length will equal a total of 136.69"
159 Extended Wheel Base Kit Includes:
10 Promaster Attachments and Pads
10 L Brackets for formed rails
Length TBD
DISCLAIMER
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury
or death.
1. Do not exceed total allowable load by vehicle manufacturer.
2. Use all available attachment points on van roof.
3. Do not install roof top deck or climb on rack.
4. Check and tighten all hardware after 100 miles and every 500 miles there-after.
5. Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold as is and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.