Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter
Airstream Roof Vent Adapter

Airstream Roof Vent Adapter

Regular price $79.55
/

Suggested Accesories

Insulated Vent Fan Cover, attached with magnets
Sikaflex 221 Adhesive
Dicor Self-Leveling Lap Sealant-10.3 Oz. Tube
Patent Pending.These adapters solve a unique problem related to fitting or replacing the vent on an Airstream trailer or motorhome. The roof of the Airstream is curved and the vent flange is designed to seal against a flat surface. Curvature of the roof can cause leaks and induce uneven stress in the roof which may cause it to deform.  Deformation of the roof can cause water to pool along the front and back of the vent which can cause leaks.

The adapter is curved on one side the match the roof and flat on the top to accommodate the flat vent flange.

Each adapter is made to fit a specific roof curvature. Upon ordering we will reach out with instructions on how to easily measure the curvature of the roof. There is a diagram in the listing showing the method. Please make the order and then we will design the adapter. We can send a drawing of the adapter to confirm the measurements provided.  If measured properly we guarantee that the adapter will fit.

Roof Vent Adapter Install Tips
 
We recommend Sikaflex 221. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof support beams.
 
Make a tape line 1/4" beyond the adapter perimeter.
De-gloss the area with a Scotch-brite pad. No need to scuff, just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out.
 
Apply three 1/8" beads of the Sikaflex on the face of the adapter. Then, press the adapter down onto  the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use several lightly set clamps and spread out the clamp force over the whole surface area.
 
Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install.
 
If you purchased our Interior Framing Strips, using the hole that you cut locate where the transverse strips need to be placed on the longitudinal strips. Assemble the interior frame with the 2" screws provided. Once the frame is assembled it will be glued to the interior side of the roof using Sikaflex 221. If the strips ordered are not bay specific, then you may need to cut them to the length of the panel you are installing it in.
 
We recommend using butyl tape for the fan install. Cover the fan flange with 1" wide tape. Place the flange onto the adapter and press down. Then drill pilot holes through the adapter and into the van roof. You may need the 4 longer screws provided for the corners. Tighten all screws very lightly against the fan flange. Some butyl will ooze out which you can trim off.
 
Coat the fan flange, adapter and onto the roof about 1/2" with self-leveling Dicor or brush-on Flexseal. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You will cut a lot of that piece off.
 
Good idea to check the integrity and reapply the sealant every so often.
 
**Please note, if you purchased butyl tape with this order and the butyl tape is stuck to the plastic,  place it in the freezer for 15 or 20 min. It will release, then let it return to room temperature. 

DISCLAIMER: Owner and/or installer assumes all risk associated with roof top mounted items and/or components. Owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.