Products
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
- Built-In Rain Cover to always protect your RV's interior
- Powerful 10 speed intake and exhaust fan
- Thermostat to control room temperature
-
Electric opening Lid, includes remote
- Provides over 900 CFM to keep you cool and comfortable
- Brings in fresh air and removes hot musty air and odors
- Fan runs with lid closed to circulate air (Ceiling Fan Mode)
-
Easy to remove interior insect screen, no tools required
- Twin lifting arms, No more lid fluttering in high winds or when driving
- Features a powerful, fuse protected, Long life, sealed ball bearing, 12 volt fan motor and a 12 inch - 10 blade fan
- Flush mounted, easy to clean Keypad, controls fan speed, thermostat, air intake and/or exhaust functions
- Closes securely for a low profile appearance
- Fits all standard 14" x 14" roof openings
- All mounting screws and hardware included. Roof sealant must be purchased separately
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
DISCLAIMER: Owner and/or installer assumes all risk associated with roof top mounted items and/or components. Owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold as is and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
We recommend Sikaflex 221. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof support beams.
Make a tape line 1/4" beyond the adapter perimeter.
De-gloss the area with a Scotch-brite pad. No need to scuff, just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out.
Apply three 1/8" beads of the Sikaflex on the face of the adapter. Then, press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use several lightly set clamps and spread out the clamp force over the whole surface area.
Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install.
If you purchased our Interior Framing Strips, using the hole that you cut locate where the transverse strips need to be placed on the longitudinal strips. Assemble the interior frame with the 2" screws provided. Once the frame is assembled it will be glued to the interior side of the roof using Sikaflex 221. If the strips ordered are not bay specific, then you may need to cut them to the length of the panel you are installing it in.
We recommend using butyl tape for the fan install. Cover the fan flange with 1" wide tape. Place the flange onto the adapter and press down. Then drill pilot holes through the adapter and into the van roof. You may need the 4 longer screws provided for the corners. Tighten all screws very lightly against the fan flange. Some butyl will ooze out which you can trim off.
Coat the fan flange, adapter and onto the roof about 1/2" with self-leveling Dicor or brush-on Flexseal. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You will cut a lot of that piece off.
Good idea to check the integrity and reapply the sealant every so often.
**Please note, if you purchased butyl tape with this order and the butyl tape is stuck to the plastic, place it in the freezer for 15 or 20 min. It will release, then let it return to room temperature.
The option with butyl tape includes 64" of butyl tape.
Disclaimer:
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
The sheets for filling corrugations should be cut into strips and glued down with 3M 90 spray or contact glue.
Minicell Foam Insulation for Van floors. 2 lb density. Minicell is fire retardant, UV stable, hydrophobic and offers sound deadening for your application.
The sheets for filling corrugations should be cut into strips and glued down with 3M 90 spray or contact glue.
If you have questions about this product you can call Hein at 541-49O-5O98
We have added an option to our packages that contains a layer of 3M TAI insulation. This layer would lay between the corrugations after the strips have been installed and the top layer of Minicell for added insulation. The TAI is 8mm thick.
The sheets for filling corrugations should be cut into strips and glued down with 3M 90 spray or contact glue.
If you have questions about this product you can call Hein at 541-49O-5O98
The sheets for filling corrugations should be cut into strips and glued down with 3M 90 spray or contact glue.
If you have questions about this product you can call Hein at 541-49O-5O98
Please see our store for other items!
The sheets for filling corrugations should be cut into strips and glued down with 3M 90 spray or contact glue.
A quantity of one equals one adapter and one switch.
If you have questions about this product you can call Hein at 541-49O-5O98