Best Selling Products
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
2) Please let us know what year and what wheel base you have: 144 WB, 170 Regular or 170 Extended.
AC Adapter Install procedure: We recommend Sikaflex 221 or 3m Window-weld adhesive. Locate and cut the hole. You can use the adapter as a guide to mark the hole. Stay clear of roof supports, obviously. Make a tape line 1/4" beyond the adapter perimeter. De-gloss the area with a Scotch- brite pad. No need to scuff. Just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out. Apply a good amount of the Window-weld on the face of the adapter. Then press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use a lot of lightly set clamps and spread out the clamp force over the whole surface area. Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the AC install per the AC instruction. Seal the adapter and onto the roof about 1/2" with brush on bed-liner or Flexseal from the TV guy works well. Good idea to check the integrity and reapply the sealant every so often. Dicor self leveling sealant also works but looks a little messy.
DISCLAIMER:
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
DISCLAIMER: Owner and/or installer assumes all risk associated with roof top mounted items and/or components. Owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Sold as a pair, these adapters are for upgrading the speakers in the the front doors of 2007 to 2018 NCV3 Sprinter vans. The factory door panel and speaker grill is retained for a stealth factory look. This is a crucial step to enjoying better sound quality in your van.
The adapters were designed in 3D CAD and they are machined on a CNC router. The holes in the adapter are perfectly located and countersunk to mount over the factory posts and be secured with the original screws. Then you drill holes in the adapter ring for your speakers and secure them with sheet metal screws. We highly recommend installing 3M Thinsulate(TM) behind the door panel at the same time.
Material for the adapters is 3/4 thick expanded PVC. It won't absorb moisture like MDF or wood and holds screws well without splitting. O.D. is 6.5" (165mm). Thickness is 3/4" (19mm). There are many ID sizes to accommodate the cutout diameter needed for the speaker. Please continue reading to learn more about speaker sizing...
While shopping for speakers look for 6 1/2 or 6 3/4 speakers. COAX are the best bang for your buck and component speakers are potentially the best sound but involve replacing the dash tweeters and installing a crossover. Most 6 1/2" speakers require a 5" ID cut out diameter which is the size of hole the speaker will drop into. The corresponds to one of our spacers on the drop down list.
There are also what the industry calls 6 3/4" speakers which allows for a bigger cone and improved base response. These speakers require the 5.62 or 5.75 ID cutout diameter (hole). We have 5.62 and 5.75 ID adapters for these speakers. Do not choose speakers with thick cast aluminum or plastic frames with protruding terminals. These are too large to fit into the smaller hole in the door sheetmetal. It is best to choose a speaker with a thinner formed metal frames and terminals that can be bent slightly should they interfere. Also do not choose a speaker that has a thick frame above the mounting face. This will interfere with the door panel. Overall height of the spacer and speaker should not exceed 1". The door panel can be trimmed to clear a taller speaker. Please contact us if you need help choosing or verifying the fit of a particular speaker.
Here are some specific suggestions of speakers that should fit.
Rockford Fosgate Prime R1675x2, these would take the 5.75ID size,
JBL GT7-6, these would take the 5.625 ID size. If you choose the component version you may have to modify the adapters.
Sprinter door speaker wire color code:
Left Front Speaker Positive Wire (+): Brown/Violet
Left Front Speaker Negative Wire (-): Brown/Dark Green
Right Front Speaker Positive Wire (+): Brown/Orange
Right Front Speaker Negative Wire (-): Brown/Dark Blue
Custom sizes are available. Please send the cut out diameter or ID in inches or millimeters.
We are adding an option to include 3 linear feet of Thinsulate (tm) for the driver and passenger doors.
We highly recommend our interior support framing system.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
These engineered ABS plastic mud flaps offer more coverage and better protection than any other offerings. There are two parts as shown in the listing photos. The large lower portion attaches to the fender and liner and a smaller flaplet attaches to the door trim. The lower portion extends far to the inside for better protection of the vehicle under-body.
Please note that optional factory (OEM) plastic fender liners are required (not included) to install and secure these mudflaps.
****We have found that the mudflaps do not work with the aftermarket fender liners that we are selling on our site. We are currently looking into a solution.
The flaps are secured with a combination of push pins and screws plus a bracket to help stabilize the inner end of the lower part.
There is some minor drilling involved and installation is much simpler if front wheels can be removed. Be sure to support vehicle on jack stands when wheels are off.
All hardware and instructions are included. Please refer to listing photos before purchase.
You can text Hein at 54l-49O-5O98 for assistance
Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose
Patent Pending. Sold in pairs. Ford Transit tower brackets. Laser cut, CNC formed tower brackets for use with 15 series 8020 square crossbars to mount solar panels and other accessories to the roof of Ford Transit vans using factory supplied OEM mounting locations. Crossbars are NOT included.
Available with clear or black anodized finish. Towers have EDPM pads to protect paint on roof of van and help seal against moisture. Includes hardware required to mount to van and attach 8020 crossbars. 80/20 bars are NOT included. Order crossbars 55.25" long and tapped 5/16-18 in both ends. Please visit 8020.net to spec and order crossbars. Please contact us for assistance.
*Black Anodizing may fade over time due to sun exposure.
Do not exceed 20 lbs load per tower. Not intended as a rack for hauling large or heavy items. Do not exceed total roof top weight allowed by vehicle manufacturer. Please contact us with any questions about how to use this product.
select 'square' for use with 15 series 8020 square profiles (uses 55.25" crossbars)
select 'rounded' for use with 1517 8020 rounded profile (uses 55.25" crossbars)
select 'extended' if the crossbar needs to extend beyond the tower. Compatible with both rounded and square 8020 profiles. This version does not cap the end of the crossbar so separate caps can be purchased with the 8020. Maximum extension beyond tower not to exceed 6". Not suitable for mounting heavy awnings not otherwise supported.
Please take a look at our support tabs for mounting solar panels to the cross bars, item number
141878685652. We also have a listing for 8020 cross bars, item number 132871157220.
If you have questions about this product you can call Hein at 541-49O-5O98
Failure to follow warnings below may allow rack to
come loose from vehicle and cause injury or death.
If in doubt, please submit rack plans or photos for
evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated
with roof top mounted items and/or components.
Van owner and/or installer recognizes and agrees that
this product, and each of its component parts, is sold
“as is” and that seller makes no representation or
warranty of merchantability that the product is fit for
any particular purpose.
IMPORTANT SAFETY WARNINGS:
* Do not exceed 20 lbs load on each tower.
* Tower spacing down length of roof not to exceed 30"
* Do not allow solar panels to overhang side of roof.
* Do not extend any component more than 4" beyond forward
or rearward most towers.
* Do not extend crossbar more than 4" beyond slot in tower
* Do not exceed total allowable load by vehicle manufacturer.
* Use all available attachment points on van roof.
* Do not install roof top deck or climb on rack.
* Check and tighten all hardware after 100 miles
and every 500 miles there-after.
* Check overall integrity of rack every 500 miles
or monthly whichever is more frequent.
Assembly:
* Refer to diagram.
* Use all parts and hardware.
* Tab that bridges or passes through slot in tower
must be used. DO NOT OMIT TAB
* Torque 5/16-18 hardware to 8 ft-lbs
* Use Loctite blue on any connection without toplock nut.
This kit includes: scissors, 4ft flexible rod and high strength string. Helpful products for installing your Thinsulate.
If you order with a roll of Thinsulate the package will be inside the roll.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
If you have questions about this product you can call Hein at 541-49O-5O98
Sold as each. This is the length you will need to install with our 8020 Sprinter tower brackets, Sprinter High Roof.
See our Sprinter tower brackets and our Tabs to connect solar panels to 8020.
Please contact Hein if you need help with your layout. 541-490-5098
Some scratching may occur in shipping.
Under vehicle battery box for Sprinter NCV3 2500 and 3500, 144WB and 170WB. Spacious heavy duty formed steel box for single or multiple batteries. Battery box includes 2 battery hold downs and hardware as shown in pictures.
These fit under the chassis on the drivers side next to the fuel tank.
If you have a stock rear heater in the passenger van this box will not fit.
BATTERY BOXES are Powder Coated!
Batteries not included.
If you have questions about this product you can call Hein at 541-49O-5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Formed aluminum towers for directly mounting specifically sized solar panels to front and rear positions on Ford Transit vans. No crossbars or other framing needed.
Use solar panel approximately 58.3 x 26.2 like Rich Solar 200 watt model. Other panels with similar dimensions will also work.
Front position utilizes OEM (factory) roof attachment points 1 and 2 (from front) which are present on all length Transit vans (130,148 and 148 extended). Rear position utilizes OEM roof attachment points 3 and 4 which are only available on 148 regular and extended vans. See diagram (148 regular length shown)
Design is patent pending.
All hardware is included. Towers are designed for solar panels only. Some fading can occur due to sun exposure. Load on each tower not to exceed 20lbs
If you have questions about this product you can call Hein at 541-49O-5O98
DISCLAIMER
Failure to follow warnings below may allow rack to come loose from vehicle and cause injuryor death.
1. Do not exceed 20 lbs load on each tower.
2. Do not extend any component more than 4" beyond forward or rearward most towers.
3. Do not exceed total allowable load by vehicle manufacturer.
4. Use all available attachment points on van roof.
5. Do not install roof top deck or climb on rack.
6. Check and tighten all hardware after 100 miles and every 500 miles there-after.
7. Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.WARNING!
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
- Do not exceed total allowable load by vehicle manufacturer.
- Use all available attachment points on van roof.
- Do not install roof top deck or climb on rack.
- Check and tighten all hardware after 100 miles and every 500 miles there-after.
- Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
D-Ring lugs for the Ford Transit. Includes hardware.
Made out of aluminum then hard anodized black. Hardware to attach to 8020 included.
8020 bars not included.
Sold as a pair. The pads come with 3M VHB peel and stick adhesive (more robust, adheres and seals pad to van - more difficult to remove). Do no exceed maximum roof loading as recommended by vehicle. There is a drawing in the images above that will allow you to determine how long the rails need to be for your van. Please call or write for assistance. It is recommended that the rails not extend beyond the front or rear bracket by more than 4".
If you have questions about this product you can call Hein at 541-49O-5O98
WARNING!
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
- Do not exceed 20 lbs load on each tower.
- Do not extend any component more than 4" beyond forward or rearward most towers.
- Do not exceed total allowable load by vehicle manufacturer.
- Use all available attachment points on van roof.
- Do not install roof top deck or climb on rack.
- Check and tighten all hardware after 100 miles and every 500 miles there-after.
- Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
These panels fit in the upper part of the door on all 2007 to present highroof Sprinter vans. They are available in fine textured white, black, or grey Celtec which is a durable PVC based plastic composite board. Thickness is ~1/4" (6mm).
The panels mount to the door with black plastic automotive style push pins included. No tools are required. The pins are very secure and won't allow the panel to come out or rattle. We have a variety of speaker sizes available for this rear door panel. Our sizes equal the cut out dimension of the speaker.
You can call or message us if you need help determining the size.
Left is driver side.