ProMaster Products

• Delivers more acoustic absorption per unit weight vs. competitive products
• Helps customers meet mass reduction goals
• Non-woven sound absorbing fibers create a quieter vehicle environment
• Hydrophobic fibers resist moisture, mold and mildew

Add our Thinsulate Installation kit: scissors, 4ft flexible rod and high strength string.  We will ship it inside your roll of Thinsulate.

Recommend using 3M 90 Adhesive Spray to apply the white fiber side to the Van skin.

Approximate amounts needed to insulate the walls, ceiling, doors and cab area:
144 WB Sprinter,148 WB Ford Transit with slider window & window in back doors = 50 linear feet
Promaster 159 WB = 60 linear feet
170 WB Sprinter = 60 linear feet
170 WB Extended Sprinter = 70 linear feet

Any order over 45 linear feet will ship in two rolls.

Please call if you are in Alaska or Hawaii for shipping 541-49O-4292

The framing strips are expanded PVC and bonded to the roof with a thick bead of Sikaflex 221.  They are more flexible than wood and plenty strong to support the vent and keep it from jiggling. We double them up when installing roof top air conditioners. They are essential if the span between the OEM roof beams is more than 18". They also provide a backing for the screws that hold up the vent interior bezel. They should be placed 1/4" away from the edge of the hole so the screws for the vent go into the strips. They are a generic size and will need to be cut to length. These strips are not contoured to the van corrugations.

We can make adapters for offset locations. Please contact us so we can verify size and location.

Roof Vent Adapter Install procedure:
We recommend 3m Window-weld or Sikaflex 221 adhesive. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof supports, obviously. Make a tape line 1/4" beyond the adapter perimeter. De-gloss the area with a Scotch- brite pad. No need to scuff. Just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out. Apply three 1/8" beads of the Window-weld on the face of the adapter. Then press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use a lot of lightly set clamps and spread out the clamp force over the whole surface area. Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install. We recommend using butyl tape for the fan install. Cover the fan flange with 1 1/8" wide tape. Place onto of adapter and press down. Then drill pilot holes through the adapter and into the van roof. If the screws are going to go into a roof support beam then drill a clearance hole in the beam. You only want the screw to engage the adapter and outer skin. Use a step drill to keep from plunging through the skin. You may need longer screws. Tighten them very lightly against the fan flange. Some butyl will ooze out which you can trim off. Coat the fan flange adapter and onto the roof about 1/2" with brush on bed-liner or Flexseal from the TV guy works well. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You'll cut a lot of that piece off. Good idea to check the integrity and reapply the sealant every so often. Dicor self leveling sealant also works but looks a little messy.

DISCLAIMER

Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.  

***Not Compatible with Power Seats***

Amazing Auto swivels attach to the Driver and Passenger seat base to allow the seats to spin and latch into different positions.

• 1-1/2 inch tall
• Heavy Duty design
• Offset design allows for seat to spin without opening door
• These are not the cheap AliExpress seat swivels

Installation Video: https://youtu.be/YubKqNS78pE

All Amazing Auto swivels come with the TRUE U.S. DOT FMVSS 207 test report. 
U.S. Patent Pending: 297.37.385, 297.34.122
Past DOT FMVSS 207

Sprinter years 2007-2023    D 001 and P 002

Promaster years 2014-2023  D 005 and P006

Transit years 2014-2023   D 003 and P 004

These above are all: 18.3in (465mm) x 18.3in (465mm) x 1.5in (37mm)

Chevy Express years 1997-2023  D 007 and P 008 is 14.25in. x 13.15in x 1.75in

28lbs

DO NOT USE WITH ENGINE RUNNING DUE TO RISK OF EXHAUST GASES ENTERING THE VEHICLE.

If you have questions about this product you can call Hein at 541-49O-5O98

Check out our other items!

Patent pending adapter matches the contour of the OEM roof so an Artic Tern Skylight mounts to a flat surface. Perimeter of adapter matches vent cover for best performance and appearance. Prevents distorting the roof sheet metal or vent flange. Can be used as an aid for locating the fan. Adapters are CNC machined out of  UV and fire resistant expanded PVC. The vent mounts to the outside adapter. The outside adapter will fit anywhere along the center cargo area of the roof. We recommend 3M Window-weld or Sikaflex 221 adhesive for adhering the adapter to the roof. Additionally, we recommend that you seal the adapter and roof light after it is installed with a membrane sealant such as Dicor.

If you are ordering this for a Sprinter we can produce them for the NCV3 or VS30, 2007 to present.

The order will include an interior support frame.

Outside dimensions are 23 1/2" x 33"

Inside opening dimensions are 19.75" x 27.6"

Artic Tern Skylight is not included.  

Photo shown is on a Promaster.

When purchasing an adapter for a van please include a note indicating where you want to place the vent so we can produce the appropriate geometry to match the roof in that location.  You are also welcome to send a photo to 541 49O 5O98. Please include your name if sending photo.

If ordering for a Sprinter we commonly ask for this measurement and information about the van:

1) Please take a measurement from the center of the large plug on the rear of the van to the back edge of the hole you will cut. Photo of the plug is below.

2) Please let us know which Wheel Base you have, 144 WB, 170 Regular or 170 Extended. The RTX opening is 15 1/2" long x 14 1/8" wide.

DISCLAIMER: Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.  

Insulate RV vent cover attached with magnets. Ripstop nylon facing with insulated core.  Sewn in magnets keep cover firmly attached to interior bezel of the vent. Magnets and superglue included. 

This fits the 14 x 14" Maxxair Fans.

MAGNET WARNING

Neodymium magnets are strong and can pinch skin. They may interfere with medical devices.

DO NOT LET CHILDREN PLAY WITH MAGNETS.

The magnets are brittle and can break or chip easily. Sliding magnets off the stack works best.

Broken magnets can still be used but we also include 2 extra magnets.

Keep magnets away from ferrous metals or they will jump to it.

Installation instructions:

1. Remove vent bezel by removing 4 screws holding it to ceiling.

2. Place vent cover on flat work surface making sure side labeled UP is visible and sewn on tab will be facing forward when back in vehicle.

   This is very Important due to magnet polarity.

3. Place and align vent bezel on top of cover.

4. Distribute 12 magnets on back of bezel flange. The 4 round magnets are placed in the middle 2 spots on each side. They will snap to the locations of the magnets in the cover. See listing photo for location of magnets.

5. Make sure the cover stays aligned with the bezel.

6. Pick up each magnet and place a drop of glue on the bezel.

   Then let magnet find it's place again. Do this for each of the 12 magnets.

7. Let glue set completely. Takes a few minutes.

8. Re-attach bezel to ceiling with screws removed in step 1.

9. Cover will now snap onto it and be held by magnets.

10. Front panel with tab can be folded over to allow partial 1/3 opening.

Please call Hein for assistance. 541-49O-5O98

Sold as a pair, these adapters are for upgrading the speakers in the the front doors of the Promaster van. The factory door panel and speaker grill is retained for a stealth factory look. This is a crucial step to enjoying better sound quality in your van.

The adapters were designed in 3D CAD and they are machined on a CNC router. The holes in the adapter are perfectly located and countersunk to mount over the factory posts and be secured with the original screws. Then you drill holes in the adapter ring for your speakers and secure them with sheet metal screws. We highly recommend installing 3M Thinsulate(TM) behind the door panel at the same time.

Material for the adapters is 3/4 thick expanded PVC. It won't absorb moisture like MDF or wood and holds screws well without splitting. O.D. is 6.5" (165mm). Thickness is 3/4" (19mm). There are 3 ID sizes to accommodate the cutout diameter needed for the speaker. Please continue reading to learn more about speaker sizing...

While shopping for speakers look for 6 1/2 or 6 3/4 speakers. COAX are the best bang for your buck and component speakers are potentially the best sound but involve replacing the dash tweeters and installing a crossover. Most 6 1/2" speakers require a 5" ID cut out diameter which is the size of hole the speaker will drop into. The corresponds to one of our spacers on the drop down list.

There are also what the industry calls 6 3/4" speakers which allows for a bigger cone and improved base response. These speakers require the 5.62 or 5.75 ID cutout diameter (hole). We have 5.62 and 5.75 ID adapters for these speakers. Do not choose speakers with thick cast aluminum or plastic frames with protruding terminals. These are too large to fit into the smaller hole in the door sheetmetal. It is best to choose a speaker with a thinner formed metal frames and terminals that can be bent slightly should they interfere. Also do not choose a speaker that has a thick frame above the mounting face. This will interfere with the door panel. Overall height of the spacer and speaker should not exceed 1". The door panel can be trimmed to clear a taller speaker. Please contact us if you need help choosing or verifying the fit of a particular speaker.

Here are some specific suggestions of speakers that should fit.

Rockford Fosgate Prime R1675X2 = 5.750 ID
JBL GT7-6 = 5.625 ID

Please note that we are able to make custom sizes.

While you have your door panel removed it is a good idea to put some thinsulate in it? Video is on a Ford Transit but it is the same process.

If you have questions about this product you can call Hein at 541-49O-5O98

Popular, 12 volt rooftop air conditioner from Dometic.  Includes Dometic's wiring and hardware kit.

Shop our Patent Pending AC roof adapters to make the install easier.

Sprinter

Transit

Postmaster

Typically ships within 5 business days directly from our supplier and can take another 5-7 days to arrive via truck freight. 

6,824 BTU.

Compact size leaves more space for solar panels and other things on your van’s roof.

Only uses 19 amps of energy in eco mode – power consumption ranges between 10 amps to 58 amps.

Recommended to be used with a battery bank of 180 amp hours or larger.

Suitable for ambient temperatures between 41 and 126 degrees Fahrenheit.

Includes remote control.

This unit is AC only, there is no “fan only” mode for recirculating air.

One year manufacturer warranty.

The opening size is 15 1/2 by 14 1/8.

Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.  

INSTALLATION VIDEO:

These are strips that help hold down the vent flange and more equally distribute the clamping force of the screws. Made from .090 thick aluminum and unpainted. Recommend covering screws and plates with self leveling sealant.

Strips fit the Maxxair Deluxe Fan 7500K, 7000K, 6200K and 5100K.

If you have questions about this product you can call Hein at 541-49O-5O98

Patent pending adapter matches the contour of the OEM roof so a Midi Heki Roof Light mounts to a flat surface. Perimeter of adapter matches vent cover for best performance and appearance. Prevents distorting the roof sheet metal or vent flange. Can be used as an aid for locating the fan. Adapters are CNC machined out of UV and fire resistant expanded PVC. The vent mounts to the outside adapter. The outside adapter will fit anywhere along the center cargo area of the roof. We recommend 3M Window-weld or Sikaflex 221 adhesive for adhering the adapter to the roof. Additionally , we recommend that you seal the adapter and roof light after it is installed with a membrane sealant such as Dicor.

Fits a cut out dimension of 500mm x 700mm.

Midi Heki Roof Light is not included.

Photo shown is on a Promaster.

When purchasing an adapter for a Sprinter Van please include a note indicating where you want to place the vent so we can produce the appropriate geometry to match the roof in that location. We will need to know the exact placement of the Skylight. We will need a measurement from the CENTER of the small plug in the rear of the van to the back edge of the opening that you will cut. We also need to know if your van is a 144WB, 170 WB or 170 Extended wheel base. You are also welcome to send a photo to 541 49O 5O98. Please include your name if sending photo. Standard locations for Sprinter vans can be found in the drop down list for this item https://www.ebay.com/itm/132298140143

If you have questions please call Hein 541 49O 5O98