Newest Products
Please contact Hein 541 49O 5O98 if you have questions about this product.
Front box 9021713
inside dimensions
height 16" width 11.5" depth 2.75"
opening size
height 15.25 width 11.25" corner radius 1"
Middle box 9021750
inside dimensions
height 16" width 11.45" depth 2.75"
opening size
height 15.25 width 11.2" corner radius 1"
Rear box 9021755
inside dimensions
height 16" width 9" depth 2.75"
opening size
height 15.25 width 8" corner radius 1"
note: depth is from
front face of panel
which is .75 thick
These are great for mounting electronics such as inverters, fuse panels, solar controllers, DC-to-DC chargers, switches, etc. Holes can be cut or drilled into sides of box for cable/wire routing. Thick back panel holds screws well for mounting components. Plastic construction is non conductive for increased electrical safety. There is room for back lighting with LED strip at top inside of box. Fits behind wall panels.
Please contact Hein at 541 49O 5O98 if you have questions.
We are honored to help you with your van build.
Sold as a pair.
Please call Hein for technical support. 54I 49O 5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
- Reflects up to 97% of Radiant Heat, Excellent Vapor Barrier for Multiple Applications
- Easy To Work With, Project and DIY Friendly, Flexible and Durable, Cuts Easily With Razor Knife
- Insect, Bird and Rodent Resistant, Non Toxic and No Itching
- Indoor Air Quality Rated Reflective Insulation and Weatherization Product
Combining 7/32" Closed Cell Foam (not bubble packaging material) and Pure Aluminum Foil (not metalized plastic) The Low-E SSR line of products provides performance and appearance for your Insulation upgrades of choice. Low-E meets the Indoor Air Quality standards set forth by California 01350, is mold and mildew resistant as well as a vapor barrier.
This Low-E is 60" wide, 1 linear foot is 5 square feet.
Low-E is FMVSS 302 certified (federal motor vehicle safety standard).
If you have questions about this product you can call Hein at 541-49O-5O98
One pair. Pads with inserts and hardware only, this does not include the Thule Bracket.
Peel and stick plate for attaching Thule leg bracket to side of vehicle. These ABS plates have 3M VHB tape for attaching to vehicle and 2 brass threaded inserts for attaching Thule leg brackets. Eliminates the need to drill holes in the vehicle. ABS plastic plates can be heated with a heat gun to conform to modestly curved surfaces. Locate and mark, Gently heat for 2-3 minutes from top until plastic becomes a little soft. Remove VHB backing and gently press against side of vehicle. Be sure of placement as VHB sticks on contact and can not be easily removed. Allow 24 hours cure before using leg bracket.
Disclaimer
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
10 ft stick of Unistrut: www.homedepot.com/p/0/100164315
1/4-20 unistrut nuts: www.homedepot.com/p/0/100115936
1" diameter caps for the ends: www.homedepot.com/p/203661028
These plugs from Amazon work a little better: www.amzn.to/2P2zJQT
Recommend using 3M 90 Adhesive Spray to apply to the Van skin.
Tips for insulating: http://impact3d.com/Thinsulate_installation.html
Please call if you are in Alaska or Hawaii for shipping 541-49O-4292
The red switch shown in the dash picture is not available.
If you have questions about this product you can call Hein at 541-49O-5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Dometic Seitz Mini Heki Plus Roof Light, 43 - 60MM roof thickness. Color of the Heki Mini and inside shade is more a creamy tan color.
Dometic SEITZ Mini Hekiplus for motorhomes and caravans. Small roof light. Lightly tinted, Insulated dome with single acrylic glazing . Can be opened in three different positions (including a poor weather position). Inner frame with darkening fly screen (can be adjusted separately).
This Roof Light will come with a seal so the rain will not come in when driving. Also know as Non-Forced Ventilation.
Specifications:
Dimensions product depth 20 7/16 "
Dimensions product width 21 "
Net weight 7.28 lbs
Operation is Manual Lever
Fits in a 400 x 400 mm opening.
We highly recommend our roof adapters for this roof light.
WARNING!! Please verify the opening requirement on your Maxxair Fan. If it is 400mm x 400mm you need to purchase an adapter from our Ford Transit Euro Adapter listing.
Pair with our Insulated Vent Fan Cover and Maxxfan Deluxe 7500K or 7000K Electric Lid Opening
Patent Pending adapter matches the contour of the OEM roof so a standard RV style vent mounts to a flat surface. Prevents distorting the roof sheet metal or vent flange and can be used as an aid for locating the fan. They are CNC machined out of UV and fire resistant expanded PVC. The fan mounts to the outside adapter. Fan adapters work with the Maxxfan Deluxe series and the Fan-tastic Vent fans.
IMPORTANT
Fan adapters work with the Maxxfan Deluxe series and the Fan-tastic Vent fans.
The outside adapter will fit anywhere along the cargo part of the roof. Longer screws than came with the vent fan may be needed.
The vent adapter outside dimension is 16 3/4 X 16 3/4. If you are using a Maxxfan vent our adapter fits the deluxe series, other Maxxfan vents have a wider flange. You will need a wider adapter. Please text Hein at 541-490-5098 for help.
If you order the framing strips they will come in a separate box.
The option with butyl tape includes 64" of tape.
We make adapters to fit air conditioners and adapters for offset locations. Please contact us so we can verify size and location.
The Low Roof Vent Adapter will also fit just ahead of the cargo area on the Mid Roof Transit.
Roof Vent Adapter Install Tips
We recommend Sikaflex 221. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof support beams.
Make a tape line 1/4" beyond the adapter perimeter.
De-gloss the area with a Scotch-brite pad. No need to scuff, just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out.
Apply three 1/8" beads of the Sikaflex on the face of the adapter. Then, press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use several lightly set clamps and spread out the clamp force over the whole surface area.
Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install.
If you purchased our Interior Framing Strips, using the hole that you cut locate where the transverse strips need to be placed on the longitudinal strips. Assemble the interior frame with the 2" screws provided. Once the frame is assembled it will be glued to the interior side of the roof using Sikaflex 221. If the strips ordered are not bay specific, then you may need to cut them to the length of the panel you are installing it in.
We recommend using butyl tape for the fan install. Cover the fan flange with 1" wide tape. Place the flange onto the adapter and press down. Then drill pilot holes through the adapter and into the van roof. You may need the 4 longer screws provided for the corners. Tighten all screws very lightly against the fan flange. Some butyl will ooze out which you can trim off.
Coat the fan flange, adapter and onto the roof about 1/2" with self-leveling Dicor or brush-on Flexseal. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You will cut a lot of that piece off.
Good idea to check the integrity and reapply the sealant every so often.
**Please note, if you purchased butyl tape with this order and the butyl tape is stuck to the plastic, place it in the freezer for 15 or 20 min. It will release, then let it return to room temperature.
If you have questions about this product you can call Hein at 541-49O-5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
diameter holes in the correct locations to match up to the positions of the clips on the van. If using slotted channel it is possible that you will need to enlarge the slots in the strut just a to make them fit.
DISCLAIMER
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
- Do not exceed total allowable load by vehicle manufacturer.
- Use all available attachment points on van roof.
- Do not install roof top deck or climb on rack.
- Check and tighten all hardware after 100 miles and every 500 miles there-after.
- Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Aluminum plate for covering OEM AC hole and ports and installing RV vent in center. For Sprinter 2007 to 2018 with factory installed roof AC. Plates are .090 thick unfinished aluminum with VHB tape pre-applied for bonding to roof. Also includes 3 smaller plates for covering 3 ports. Prep surface of roof by cleaning and de glossing with isopropyl alcohol and scotch-brite pad. Apply VHB in warm conditions and use heat and pressure to set after installation. Seal perimeter edge of plates with 3M 4412N extreme sealant tape or Dicor self leveling sealant. If using tape work from rear edge forward so front pieces overlap rear pieces. Remove release film from top of tape so it can be laid around corners and next layer will stick. Recommend that plate and sealant can be painted to match vehicle. RV vent is mounted with butyl tape provided. 14x14" opening. OEM AC hole will need to be enlarged to 14 by trimming approximately 1/4" along front edge. This can be done after plate is installed.
The outside dimension of the plate is 15.25" x 32.5"
This Plate will NOT work on the VS30, please see this link. https://diyvan.com/collections/ac-adapters/products/sprinter-delete-plate
We also offer the AC Replacement Plate with no hole.
Please call Hein for technical support. 541 49O 5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
We recommend using 3M 90 Adhesive Spray to apply the white fiber side to the Van skin.
We also sell 3M SM600L which is the thickest grade engineered for vehicles
Sold by the each.
If you have questions please call, 541-49O-5O98
- Delivers more acoustic absorption per unit weight vs. competitive products
- Helps customers meet mass reduction goals
- Non-woven sound absorbing fibers create a quieter vehicle environment
- Hydrophobic fibers resist moisture, mold and mildew
Add our Thinsulate Installation kit: scissors, 4ft flexible rod and high strength string. We will ship it inside your roll of Thinsulate.
Recommend using 3M 90 Adhesive Spray to apply the white fiber side to the Van skin.
Approximate amounts needed to insulate the walls, ceiling, doors and cab area:
144 WB Sprinter,148 WB Ford Transit with slider window & window in back doors = 50 linear feet
Promaster 159 WB = 60 linear feet
170 WB Sprinter = 60 linear feet
170 WB Extended Sprinter or Transit 148 Extended = 70 linear feet
Any order over 45 linear feet will ship in two rolls.
Please call if you are in Alaska or Hawaii for shipping 541-49O-4292