Newest Products
DISCLAIMER: Owner and/or installer assumes all risk associated with roof top mounted items and/or components. Owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
DISCLAIMER: Owner and/or installer assumes all risk associated with roof top mounted items and/or components. Owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold as is and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
If you have questions or require technical support regarding this or any of our products then please call Hein at 541-49O-5O98
Check out our other items!
Swivel for Powered Seats
Amazing Auto swivels attach to the Driver and Passenger seat base to allow the seats to spin and latch into different positions.
- 1-1/2 inch tall
- Heavy Duty design
- Offset design allows for seat to spin without opening door
- These are not the cheap AliExpress seat swivels
Installation Video: https://www.sprinterswivel.com/index.php?route=information/information&information_id=9
All Amazing Auto swivels come with the TRUE U.S. DOT FMVSS 207 test report.
U.S. Patent Pending: 297.37.385, 297.34.122
Past DOT FMVSS 207
Transit years 2014-2024 Driver DPD03E and Passenger P006
18.3in (465mm) x 18.3in (465mm) x 1.5in (37mm)
28lbs
A quantity of one equals one adapter and one switch.
If you have questions about this product you can call Hein at 541-49O-5O98
If you have questions about this product you can call Hein at 541-49O-5O98
Xantrex 12V 105Ah Lithium-Ion Battery
If you have questions please call, 541-49O-5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
* Black Anodizing may fade over time due to sun exposure.
Towers come with hardware to attach to the van. Additional hardware to attach the platform may be required. The towers have rubber pads to seal the roof holes and protect the van finish. Easy to install with hand tools.
If you have questions about this product you can call Hein at 541-49O-5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
These engineered ABS plastic mud flaps offer more coverage and better protection than any other offerings. There are two parts as shown in the listing photos. The large lower portion attaches to the fender and liner and a smaller flaplet attaches to the door trim. The lower portion extends far to the inside for better protection of the vehicle under-body.
Please note that optional factory (OEM) plastic fender liners are required (not included) to install and secure these mudflaps.
****We have found that the mudflaps do not work with the aftermarket fender liners that we are selling on our site. We are currently looking into a solution.
The flaps are secured with a combination of push pins and screws plus a bracket to help stabilize the inner end of the lower part.
There is some minor drilling involved and installation is much simpler if front wheels can be removed. Be sure to support vehicle on jack stands when wheels are off.
All hardware and instructions are included. Please refer to listing photos before purchase.
You can text Hein at 54l-49O-5O98 for assistance
Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose
Pair with our Insulated Vent Fan Cover and Maxxfan Deluxe 7500K or 7000K Electric Lid Opening
This adapter is for a Nisan 200 van.
Patent Pending adapter matches the contour of the OEM roof so a standard RV style vent mounts to a flat surface. Prevents distorting the roof sheet metal or vent flange and can be used as an aid for locating the fan. They are CNC machined out of UV and fire resistant expanded PVC. The fan mounts to the outside adapter. Fan adapters work with the Maxxfan Deluxe series and the Fan-tastic Vent fans.
The framing strips are expanded PVC and bonded to the roof with a thick bead of Windoweld. They are more flexible than wood and plenty strong to support the vent and keep it from jiggling. We double them up when installing roof top air conditioners. They are essential if the span between the OEM roof beams is more than 18". They also provide a backing for the screws that hold up the vent interior bezel. They should be placed 1/4" away from the edge of the hole so the screws for the vent go into the strips. They are a generic size and will need to be cut to length. These strips are not contoured to the van corrugations.
IMPORTANT
Fits a 14" x 14" opening.
Fan adapters work with the Maxxfan Deluxe series and the Fan-tastic Vent fans.
The outside adapter will fit anywhere along the cargo part of the roof. Longer screws than came with the vent fan may be needed.
The vent adapter outside dimension is 16 3/4 X 16 3/4. If you are using a Maxxair vent our adapter fits the Maxxfan Deluxe series, other Maxxair vents have a wider flange. You will need a wider adapter. Please call.
If you order the framing strips they will come in a separate box.
The option with butyl tape includes 64" of tape. If the butyl tape is stuck to the plastic, put it in the freezer for 30 minutes. It will release, then let the butyl tape return to room temperature.
We make adapters to fit air conditioners and adapters for offset locations. Please contact us so we can verify size and location.
Roof Vent Adapter Install Tips
We recommend Sikaflex 221. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof support beams.
Make a tape line 1/4" beyond the adapter perimeter.
De-gloss the area with a Scotch-brite pad. No need to scuff, just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out.
Apply three 1/8" beads of the Sikaflex on the face of the adapter. Then, press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use several lightly set clamps and spread out the clamp force over the whole surface area.
Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install.
If you purchased our Interior Framing Strips, using the hole that you cut locate where the transverse strips need to be placed on the longitudinal strips. Assemble the interior frame with the 2" screws provided. Once the frame is assembled it will be glued to the interior side of the roof using Sikaflex 221. If the strips ordered are not bay specific, then you may need to cut them to the length of the panel you are installing it in.
We recommend using butyl tape for the fan install. Cover the fan flange with 1" wide tape. Place the flange onto the adapter and press down. Then drill pilot holes through the adapter and into the van roof. You may need the 4 longer screws provided for the corners. Tighten all screws very lightly against the fan flange. Some butyl will ooze out which you can trim off.
Coat the fan flange, adapter and onto the roof about 1/2" with self-leveling Dicor or brush-on Flexseal. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You will cut a lot of that piece off.
Good idea to check the integrity and reapply the sealant every so often.
**Please note, if you purchased butyl tape with this order and the butyl tape is stuck to the plastic, place it in the freezer for 15 or 20 min. It will release, then let it return to room temperature.
Disclaimer:
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
For use with Weathertech mudflaps on Ford Transit van. These 'flaplets' attach to the cab doors and fill the gap left by the Weathertech flaps. They are made of black ABS plastic with haircell texture. They are attached to the door fender trim with 3 small screws. It is necessary to hand form the flaplet to have a slight curvature prior to installation. A heat gun can be used to heat the plastic so it is easier to form into slight curve that matches the door where it will be mounted. Do not over heat.
Kit includes right hand and left hand flaplets and 6 mounting screws.
To install:
1. Turn front wheels to provide clearance.
2. Hand form/bend flaplet into slight curve to match door. Using heat can help.
Textured side of flaplet should be toward back; smooth side toward tire.
3. Locate flaplet on door leaving 1/8" gap between it and top edge of mudflap below.
4. Drill 1/16 pilot holes for screws.
5. Install flaplet with screws provided. Do not over tighten or you may strip plastic trim on door.
6. Turn wheels other way and repeat on other side of vehicle.
You can text Hein at 54l-49O-5O98 for assistance.
Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose
Offset Adapters for the Ford Transit Mid/High Roof, fits a 14" x 14" hole. Please check the hole requirements in the manual.
Pair with our Insulated Vent Fan Cover and Maxxfan Deluxe 7500K or 7000K Electric Lid Opening
The adapter will work on either the driver side or passenger side of the van. Our measurements are taken from the Center line of the van roof to the center of the 14" x 14" hole.
Patent Pending adapter matches the contour of the OEM roof so a standard RV style vent mounts to a flat surface. Prevents distorting the roof sheet metal or vent flange and can be used as an aid for locating the fan. They are CNC machined out of UV and fire-resistant expanded PVC. The fan mounts to the outside adapter. Fan adapters work with the Maxxfan Deluxe series and the Fan-tastic Vent fans.
CLICK HERE for our Interior Supporting Framing strips.
Fan adapters work with the Maxxfan Deluxe series and the Fan-tastic Vent fans.
The outside adapter will fit anywhere along the cargo part of the roof. Longer screws than came with the vent fan may be needed.
The vent adapter outside dimension is 16 3/4 X 16 3/4. If you are using a Maxxair vent our adapter fits the Maxxfan Deluxe series, other Maxxair vents have a wider flange. You will need a wider adapter. Please call.
Roof Vent Adapter Install Tips
We recommend Sikaflex 221. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof support beams.
Make a tape line 1/4" beyond the adapter perimeter.
De-gloss the area with a Scotch-brite pad. No need to scuff, just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out.
Apply three 1/8" beads of the Sikaflex on the face of the adapter. Then, press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use several lightly set clamps and spread out the clamp force over the whole surface area.
Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install.
If you purchased our Interior Framing Strips, using the hole that you cut locate where the transverse strips need to be placed on the longitudinal strips. Assemble the interior frame with the 2" screws provided. Once the frame is assembled it will be glued to the interior side of the roof using Sikaflex 221. If the strips ordered are not bay specific, then you may need to cut them to the length of the panel you are installing it in.
We recommend using butyl tape for the fan install. Cover the fan flange with 1" wide tape. Place the flange onto the adapter and press down. Then drill pilot holes through the adapter and into the van roof. You may need the 4 longer screws provided for the corners. Tighten all screws very lightly against the fan flange. Some butyl will ooze out which you can trim off.
Coat the fan flange, adapter and onto the roof about 1/2" with self-leveling Dicor or brush-on Flexseal. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You will cut a lot of that piece off.
Good idea to check the integrity and reapply the sealant every so often.
**Please note, if you purchased butyl tape with this order and the butyl tape is stuck to the plastic, place it in the freezer for 15 or 20 min. It will release, then let it return to room temperature.
Disclaimer:
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Aluminum plate and spacer strips for covering OEM AC hole on Sprinter VS30 (2019 to present) with factory installed roof AC. Plates are .090 thick unfinished aluminum. Strips are PVC based plastic.
Vent or AC hole is 14x14
RTX hole is 15 1/2" x 14 1/8", this will include our foam seal. You may want to add a spacer to raise the unit up for head clearance inside the van and one of our interior bezels. Spacers and interior bezels.
This Plate will NOT work on the NCV3 (2007-2018) Sprinter.
Notes:
- Assembled (recommended) version comes with all strips bonded to plate. Ready to install on vehicle.
- Un-assembled version requires strips to be bonded to plate. See instructional videos below.
-
A urethane structural adhesive is required to make all bonds between strips plate and vehicle.
recommended products: 3M Windoweld, Dupont Betaseal U-458plus, Sikaflex 221 -
Plate is unpainted but can be painted to match vehicle.
5. RV vent flange is mounted with butyl tape provided. - Membrane sealant or tape recommended over the top of all seams recommended products: Dicor self leveling sealant or 3M 4412-N extreme sealing tape.
Best way to understand this product and installation is to watch these videos.
Watch our video on the AC delete plate for the RTX
Please text Hein for technical support. 541 49O 5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
The sheets for filling corrugations should be cut into strips and glued down with 3M 90 spray or contact glue.
Patent pending adapter matches the contour of the OEM roof so an Artic Tern Skylight mounts to a flat surface. Perimeter of adapter matches vent cover for best performance and appearance. Prevents distorting the roof sheet metal or vent flange. Can be used as an aid for locating the skylight. Adapters are CNC machined out of UV and fire resistant expanded PVC. The vent mounts to the outside adapter. The outside adapter will fit anywhere along the center cargo area of the roof. We recommend 3M Window-weld or Sikaflex 221 adhesive for adhering the adapter to the roof. Additionally, we recommend that you seal the adapter and roof light after it is installed with a membrane sealant such as Dicor.
If you are ordering this for a Sprinter we can produce them for the NCV3 or VS30, 2007 to present.
The order will include an interior support frame.
Outside dimensions are 23 1/2" x 33"
Inside opening dimensions are 19.75" x 27.6"
Artic Tern Skylight is not included.
Photo shown is on a Promaster.
When purchasing an adapter for a van please include a note indicating where you want to place the vent so we can produce the appropriate geometry to match the roof in that location. You are also welcome to send a photo to 541 49O 5O98. Please include your name if sending photo.
If ordering for a Sprinter we commonly ask for this measurement and information about the van:
1) Please take a measurement from the center of the large plug on the rear of the van to the back edge of the hole you will cut. Photo of the plug is below.
2) Please let us know which Wheel Base you have, 144 WB, 170 Regular or 170 Extended. The RTX opening is 15 1/2" long x 14 1/8" wide.
DISCLAIMER: Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.