Newest Products
Patent Pending. These brackets are designed for NCV3 and VS30 Sprinter high roof vans with OEM roof rails 51.875" apart. Panels around 52" are recommended. For example Newpowa 180 watt panels.
Please note: These brackets were initially made for the Renogy 175 Watt panel but Renogy has shortened the panel to 49.7". These brackets will NOT work with this panel.
Please contact us for help with your specific application if needed. Two tower brackets and all hardware are included with each kit. 2 kits are required for one panel. One additional kit is needed for attaching each subsequent panels forming one large array of multiple panels.
The brackets are mounted to the underside of the panel with 1/4-20 stainless button head cap screws (included).
DISCLAIMER:
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
1. Do not exceed 20 lbs load on each tower.
2. Do not extend any component more than 4" beyond forward or rearward most towers.
3. Do not exceed total allowable load by vehicle manufacturer.
4. Use all available attachment points on van roof.
5. Do not install roof top deck or climb on rack.
6. Check and tighten all hardware after 100 miles and every 500 miles there-after.
7. Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
DISCLAIMER: Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
This adapter fits a 400mm x 400mm opening. Please check you fan.
Fits a 400mm X 400mm opening. These fans are usually purchased in the UK. If your fan requires 14" x 14" opening please message me.
The option with butyl tape includes 64" of tape. If the butyl tape is stuck to the plastic, put it in the freezer for 30 minutes. It will release, then let the butyl tape return to room temperature.
The Low Roof Vent Adapter will also fit on the forward position on the Mid roof Transit.
The level shown in the photo is not included.
Roof Vent Adapter Install Tips
We recommend Sikaflex 221. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof support beams.
Make a tape line 1/4" beyond the adapter perimeter.
De-gloss the area with a Scotch-brite pad. No need to scuff, just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out.
Apply three 1/8" beads of the Sikaflex on the face of the adapter. Then, press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use several lightly set clamps and spread out the clamp force over the whole surface area.
Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install.
We recommend using butyl tape for the fan install. Cover the fan flange with 1" wide tape. Place the flange onto the adapter and press down. Then drill pilot holes through the adapter and into the van roof. You may need the 4 longer screws provided for the corners. Tighten all screws very lightly against the fan flange. Some butyl will ooze out which you can trim off.
Coat the fan flange, adapter and onto the roof about 1/2" with self-leveling Dicor or brush-on Flexseal. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You will cut a lot of that piece off.
Good idea to check the integrity and reapply the sealant every so often.
**Please note, if you purchased butyl tape with this order and the butyl tape is stuck to the plastic, place it in the freezer for 15 or 20 min. It will release, then let it return to room temperature.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
These are strips that help hold down the vent flange and more equally distribute the clamping force of the screws. Made from .090 thick aluminum and unpainted. Recommend covering screws and plates with self leveling sealant.
Strips fit the Maxxair Deluxe Fan 7500K, 7000K, 6200K and 5100K.
If you have questions about this product you can call Hein at 541-49O-5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Sold as each. This is the length you will need to install with our 8020 Sprinter tower brackets, Sprinter High Roof.
See our Sprinter tower brackets and our Tabs to connect solar panels to 8020.
Please contact Hein if you need help with your layout. 541-490-5098
Some scratching may occur in shipping.
Sold as a pair.
Tower Brackets are NOT included.
Please call Hein for technical support. 54I 49O 5O98
Disclaimer
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Pair with our Insulated Vent Fan Cover and Maxxair Mini Vent Non Powered
This fits a 14" x 14" opening. The adapters in the listing are centered on the roof line. If you need an offset adapter please fill out our form.
Click here for our custom adapter inquiry form.
Patent Pending adapter matches the contour of the OEM roof so a standard RV style vent mounts to a flat surface. Prevents distorting the roof sheet metal or vent flange and can be used as an aid for locating the fan. They are CNC machined out of UV and fire resistant expanded PVC. The fan mounts to the outside adapter. Fan adapters works with the Maxxair Mini Vent Non Powered Fan.
We make adapters to fit air conditioners and adapters for offset locations. Please contact us so we can verify size and location.
Roof Vent Adapter Install TipsWe recommend Sikaflex 221. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof support beams.
Make a tape line 1/4" beyond the adapter perimeter.
De-gloss the area with a Scotch-brite pad. No need to scuff, just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out.
Apply three 1/8" beads of the Sikaflex on the face of the adapter. Then, press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use several lightly set clamps and spread out the clamp force over the whole surface area.
Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install.
If you purchased our Interior Framing Strips, using the hole that you cut locate where the transverse strips need to be placed on the longitudinal strips. Assemble the interior frame with the 2" screws provided. Once the frame is assembled it will be glued to the interior side of the roof using Sikaflex 221. If the strips ordered are not bay specific, then you may need to cut them to the length of the panel you are installing it in.
We recommend using butyl tape for the fan install. Cover the fan flange with 1" wide tape. Place the flange onto the adapter and press down. Then drill pilot holes through the adapter and into the van roof. You may need the 4 longer screws provided for the corners. Tighten all screws very lightly against the fan flange. Some butyl will ooze out which you can trim off.
Coat the fan flange, adapter and onto the roof about 1/2" with self-leveling Dicor or brush-on Flexseal. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You will cut a lot of that piece off.
Good idea to check the integrity and reapply the sealant every so often.
**Please note, if you purchased butyl tape with this order and the butyl tape is stuck to the plastic, place it in the freezer for 15 or 20 min. It will release, then let it return to room temperature.
If you have questions about this product you can call Hein at 541-49O-5O98
Disclaimer
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
- Reflects up to 97% of Radiant Heat, Excellent Vapor Barrier for Multiple Applications
- Easy To Work With, Project and DIY Friendly, Flexible and Durable, Cuts Easily With Razor Knife
- Insect, Bird and Rodent Resistant, Non Toxic and No Itching
- Indoor Air Quality Rated Reflective Insulation and Weatherization Product
Combining 7/32" Closed Cell Foam (not bubble packaging material) and Pure Aluminum Foil (not metalized plastic) The Low-E SSR line of products provides performance and appearance for your Insulation upgrades of choice. Low-E meets the Indoor Air Quality standards set forth by California 01350, is mold and mildew resistant as well as a vapor barrier.
This Low-E is 72" wide, 1 linear foot is 6 square feet.
Low-E is FMVSS 302 certified (federal motor vehicle safety standard).
If you have questions about this product you can call Hein at 541-49O-5O98Shop our Patent Pending AC roof adapters to make the install easier. Sprinter, Transit, Promaster.
Typically ships within 3-4 business days and can take another 5-7 days to arrive via truck freight.
**For LTL Freight deliveries, please inspect the entire package and product before the driver leaves. If you find damage, take pictures and make sure the driver notes the damage on the BOL. If damage is found after the driver leaves, we have no recourse with the carrier, and thus, no path to a credit.**
The Plein-Aircon is an innovative rooftop mounted air conditioning system for RVs and vans. This Indel B rooftop-mounted AC features ground-breaking technology, that makes the air conditioning unit convenient, efficient, powerful, and reliable. The Indel B Plein provides 4100 BTU (1200W) of cooling.
With a built-in power supply, you can use the Plein-Aircon even while stopped, without having to idle the engine. Thanks to the Smart Switch built into the power supply, the Plein can be powered by both 12V DC and 115V AC power.
The cutting-edge 12V Samsung compressor works nearly silently, while using as low as 16 Amps per hour. It reliably cools and dehumidifies the air.
This air conditioning unit comes with multiple comfort features, as well. If you want to schedule the AC to turn on in the morning, or before you go to sleep, you can take advantage of the timer, which lets you schedule ON and OFF times down to the minute. Controlling the Plein-Aircon is made easy and intuitive with the included remote control. Set the temperature, blower speed, and fan mode from anywhere in your cabin.
Technical Specifications of the Indel B Plein-Aircon:
Input Voltage |
12V DC (115-230V AC) |
Maximum Power |
4100 BTU (1.2 KW) |
Power Consumption |
16-42 A/h |
Coolant Type |
R134a |
Fan Operating Modes |
3 speeds + auto mode |
Weight |
55.8 lbs (25.3 kg) |
External Dimensions |
9.7 x 26.4 x 31.5 in (246.4 x 670.5 x 800 mm) |
Internal Dimensions |
2 x 21 x 23.6 in (50.8 x 533.4 x 600 mm) |
Roof cut-out Dimensions |
15.8 x 15.8 in (401 x 401 mm) |
Suitable Roof Thickness |
from 1.2 to 2.75 in (30.5-70 mm) |
Disclaimer: Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
The material comes compressed; we recommend unpacking it as soon as it is received. One roll is 20 linear feet. 20ft long by 60 inches wide.
Arctic Fiber is a high-loft 100% non-woven, thermally bonded polyester insulation. The material is 2" thick after it lofts up. One roll of material is 20 feet long x 60" wide. This insulation is widely used in Alaska in the Van industry and has other uses in pads, covers on exterior pipe, flange valves and other special equipment.
- Allows Trapped moisture to pass through it without being held in place and drys out quickly.
- Polyester batt insulation will not promote mold growth.
- Lightweight and easily fabricated to desired dimensions with a utility knife or scissors.
- Is not an irritant and will not cause skin irritation.
- Passes the FMVSS302 burn rate test.
Recommend using a high temp adhesive spray to apply to the van skin.
Approximate amounts needed to insulate the walls, ceiling, doors and cab area:
144 WB Sprinter,148 WB Ford Transit with slider window & window in back doors = 50 linear feet
Promaster 159 WB = 60 linear feet
170 WB Sprinter = 60 linear feet
170 WB Extended Sprinter = 70 linear feet
Please call if you are in Alaska or Hawaii for shipping 541-49O-4292