Products
Swivel for Powered Seats
Amazing Auto swivels attach to the Driver and Passenger seat base to allow the seats to spin and latch into different positions.
- 1-1/2 inch tall
- Heavy Duty design
- Offset design allows for seat to spin without opening door
- These are not the cheap AliExpress seat swivels
Installation Video: https://www.sprinterswivel.com/index.php?route=information/information&information_id=9
All Amazing Auto swivels come with the TRUE U.S. DOT FMVSS 207 test report.
U.S. Patent Pending: 297.37.385, 297.34.122
Past DOT FMVSS 207
Transit years 2014-2024 Driver DPD03E and Passenger P006
18.3in (465mm) x 18.3in (465mm) x 1.5in (37mm)
28lbs
This kit includes: scissors, 4ft flexible rod and high strength string. Helpful products for installing your Thinsulate.
If you order with a roll of Thinsulate the package will be inside the roll.
One piece composite flooring. We offer the floor with or without the machined Minicell. We will need to know if you have a dually or not.
We also have an option to add our step well storage. The floor will be machined over the top of them. If you would like us to install the floor and the step well there will be a labor cost of $270.00 due at time of pick up. This can take 1 to 2 hours.
Composite is .44" thick and minicell is .75" thick.
FOR PICKUP ONLY!
Text Hein at 541-490-5098 for details, estimated time and pick up.
Set of 2 aluminum reinforcement strips to do one side of two beams or both sides of a single beam. Adds additional strength to the beams when installing an Air Conditioner on a Transit van. Especially important in 2 forward most bays which have the greatest span between beams. For best structural strength order two sets and do both sides of each beam.
The surface of the beams will need to be de-glossed with a scotch-brite pad to improve adhesion. Self drilling stainless screws are included. An option with 1 cartridge of Sikaflex 221 is also available.
Under vehicle battery box for Sprinter NCV3 2500 and 3500, 144WB and 170WB. Spacious heavy duty formed steel box for single or multiple batteries. Battery box includes 2 battery hold downs and hardware as shown in pictures.
These fit under the chassis on the drivers side next to the fuel tank.
If you have a stock rear heater in the passenger van this box will not fit.
BATTERY BOXES are Powder Coated!
Batteries not included.
If you have questions about this product you can call Hein at 541-49O-5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Xantrex 12V 105Ah Lithium-Ion Battery
If you have questions please call, 541-49O-5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
BATTERY BOX MUST BE PAINTED IF NOT POWDER COATED. Wash the tray with soapy water, dry, then paint the tray before installing. Rustoleum truck bed coating spray or equivalent.
Batteries not included.
Copy and paste for installation help with the 2500 http://www.impact3d.com/170_2500_midship_tray.htm
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold "as is" and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
BATTERY BOXES are Powder Coated!
If you have questions about this product you can call Hein at 541-490-5098 or text him.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Patent Pending. These brackets are designed for NCV3 and VS30 Sprinter high roof vans with OEM roof rails 51.875" apart. Panels around 52" are recommended. For example Newpowa 180 watt panels.
Please note: These brackets were initially made for the Renogy 175 Watt panel but Renogy has shortened the panel to 49.7". These brackets will NOT work with this panel.
Please contact us for help with your specific application if needed. Two tower brackets and all hardware are included with each kit. 2 kits are required for one panel. One additional kit is needed for attaching each subsequent panels forming one large array of multiple panels.
The brackets are mounted to the underside of the panel with 1/4-20 stainless button head cap screws (included).
DISCLAIMER:
Failure to follow warnings below may allow rack to come loose from vehicle and cause injury or death.
1. Do not exceed 20 lbs load on each tower.
2. Do not extend any component more than 4" beyond forward or rearward most towers.
3. Do not exceed total allowable load by vehicle manufacturer.
4. Use all available attachment points on van roof.
5. Do not install roof top deck or climb on rack.
6. Check and tighten all hardware after 100 miles and every 500 miles there-after.
7. Check overall integrity of rack every 500 miles or monthly whichever is more frequent.
If in doubt, please submit rack plans or photos for evaluation prior to final installation or use.
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
Aluminum plate and spacer strips for covering OEM AC hole on Sprinter VS30 (2019 to present) with factory installed roof AC. Plates are .090 thick unfinished aluminum. Strips are PVC based plastic.
Vent or AC hole is 14x14
RTX hole is 15 1/2" x 14 1/8", this will include our foam seal. You may want to add a spacer to raise the unit up for head clearance inside the van and one of our interior bezels. Spacers and interior bezels.
This Plate will NOT work on the NCV3 (2007-2018) Sprinter.
Notes:
- Assembled (recommended) version comes with all strips bonded to plate. Ready to install on vehicle.
- Un-assembled version requires strips to be bonded to plate. See instructional videos below.
-
A urethane structural adhesive is required to make all bonds between strips plate and vehicle.
recommended products: 3M Windoweld, Dupont Betaseal U-458plus, Sikaflex 221 -
Plate is unpainted but can be painted to match vehicle.
5. RV vent flange is mounted with butyl tape provided. - Membrane sealant or tape recommended over the top of all seams recommended products: Dicor self leveling sealant or 3M 4412-N extreme sealing tape.
Best way to understand this product and installation is to watch these videos.
Watch our video on the AC delete plate for the RTX
Please text Hein for technical support. 541 49O 5O98
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold “as is” and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.
These fit in the outer rounded positions. They will not work in the inner straight positions, see other listing. (These are not compatible with the NCV3 Sprinter) 3D printed in tough nylon plastic.
Use of a relay to carry larger loads is recommended. Not all switches have the same load (Amp) capacity. Refer to drop down list for current ratings.
SPST (single pole single throw) is simple on/off switch (most common)SPDT (single pole double throw) is on/on switch which can also be used as on/off. These can also be used for 2-way control with another SPDT.DPDT and DPST (double pole) are essentially two switches tied together and actuated simultaneously. One side can be used as simple on/off switches (same as SPDT or SPST) or to switch both negative and positive at the same time. Also wired as reversing (polarity reversing) switches.SPDT with center off means the there is a middle position that is not connected to either output Lighted switches means the light comes on when the load is energized. Refer to photos for proper connections. These will need a ground connection for the light to work.
A quantity of one equals one adapter and one switch.
The Crew Seat fillers require a 3/8 wide rabbet cut around each hole using a router. There may not be sufficient clearance to do this with the floor in the van. Removal of the floor may be necessary.
Sold by the each, 1 = 1
Wall insert mounting panel with built in box. Each item is designed for a precise fit in the lower wall openings behind driver. Attaches by clamping against back side of chassis structure. Does not require holes in sheet metal. The outside surface is flush with the surrounding sheet metal.Material is expanded PVC that does not absorb water. Great for mounting electrical components such as inverters, charge controllers and fuse panels. Cuts easily with traditional wood working tools. Use hole saw to make gauge mounts, holes for wire/cable routing, etc. Holds screws very well and will not conduct electricity.
On the newer van models you may need to move the sensor bracket in the 2nd position.
Forward box
opening size 6.875w x 13h corner radius 1"
box size 7.125w x 13.75h x 3.25 depth
depth is from face of panel. panel is .75 thick
Middle box
opening size 10w x 13h corner radius 1"
box size 10.25w x 13.75h x 3.25 depth
depth is from face of panel. panel is .75 thick
Rear box
opening size 7.5w x 13h corner radius 1"
box size 7.125w x 13.75h x 3.25 depth
depth is from face of panel. panel is .75 thick
Please contact Hein at 541 490 5098 if you have questions.
We are honored to help you with your van build.
Roof fan 12 Volt Winglet
This electric fan from G&C ensures a healthy discharge of air in your automobile.
This roof fan only extracts!
The roof fan is made of ABS. The voltage is 12 Volts and the consumption is 3 Watts.
The noise level is 32 DB. The airflow is 65 M³/H. The fan comes standard with an interior grill, shutter and saw template.
By using the 2-way switch you can turn this fan on and off, not included.
The opening in the roof is 80 mm. Construction height is 64 mm.
The fan is available in black.
* material: high quality ABS
* Function: extract air
* Opening in roof: 80 mm
* Construction height: 64 mm
* air displacement: 65 M³ per hour
Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.